• 1911 FIRING PIN EGW More Detail

    1911 FIRING PIN EGW

    Click here for price!$11.99Click here for price!$11.99

    Durable Stainless Steel; Available In Three Diameters For Precise ClearanceTough, durable firing pins are precision machined from extra-hard stainless steel to fit in the slide with .001" clearance to help eliminate primer flow with hot loads. Helps prevent jams and misfires caused by the primer backing out. Available in three diameters; select the diameter that provides just enough clearance through the hole in the firing pin stop of your gun. .068 normally fits Colt and Caspian 9mm/.38 Super/.40/10mm. .075 fits Springfield Armory 9mm/.38 Super/10mm/current-production .45 ACP. .093 fits most .45 ACP, including older-production Springfield. Fit may vary; measure your gun to be sure you select the correct size pin. 1911, Issue:11, Page:021 Big Book Catalog, Issue:69, Page:114 Sinclair, Issue:1A, Page:019

    HOT!
  • P226 9MM PARTS KIT SIG SAUER More Detail

    P226 9MM PARTS KIT SIG SAUER

    Click here for price!$30.99Click here for price!$30.99

    Sig Sauer Parts Kits allow for periodic maintenance of Sig pistols.  The kits include a selection of the most frequently requested replacement parts.  Kits include: decocking lever spring, slide catch lever spring, trigger bar spring, recoil spring, slide pins & grip screws.  Note, kits for P220 & P232 also include washers with the grip screws. Big Book Catalog, Issue:69, Page:208

    HOT!
  • SINGLE ACTION ARMY 1ST,2ND,3RD GEN BOLT SMITH ENTERPRISE More Detail

    SINGLE ACTION ARMY 1ST,2ND,3RD GEN BOLT SMITH ENTERPRISE

    Click here for price!$64.99Click here for price!$64.99

    Rebuilding, Accurizing, Tuning & RestorationHeat-treated, spring steel, hardened and oversize action parts for rebuilding and accurizing Colt Single Action Army revolvers. All are slightly oversize to allow precise fitting. Bolts are radiused between the forks to resist breakage, extra wide lug provides for exact fit to cylinder locking slots. 1st Gen. bolt is shaped and contoured to match the original. 2nd/3rd Gen. bolt will fit all 1st, 2nd, 3rd generation guns. Hand, for 1st and 2nd generation guns, is hardened and heat treated to improve durability. Left slightly long for precise fitting. Big Book Catalog, Issue:69, Page:231

    HOT!
  • 1911 EXTRACTOR BROWNELLS More Detail

    1911 EXTRACTOR BROWNELLS

    Click here for price!$27.99 - $52.90Click here for price!$27.99 - $52.90

    Extra-Tough For Long Life & Reliable ExtractionMachined steel extractors for 70 and 80 series 1911 pistols are hardened and heat-treated for consistent operation in competitive and tactical use. Available in blue or stainless steel. Stainless models have a unique copper color from the heat-treating process. Leave as is or off for a more traditional look. 1911, Issue:11, Page:011 Big Book Catalog, Issue:69, Page:104 Sinclair, Issue:1A, Page:011

    HOT!
  • GRAND MASTERS, LLC- RUGER® REPLACEMENT BASE PIN POWER CUSTOM More Detail

    GRAND MASTERS, LLC- RUGER® REPLACEMENT BASE PIN POWER CUSTOM

    Click here for price!$32.95Click here for price!$32.95

    These Single Action Revolver replacement pins are oversized to reduce “cylinder wobble”. The head has been redesigned for a more positive grip for easy removal, and is also shorter than the factory head to allow for longer ejector rod travel that improves ejection.  Some applications may require minor fitting, depending on burrs in holes and hole alignment. Big Book Catalog, Issue:69, Page:231

    HOT!
  • BULLET PROOF™ FIRING PIN STOPS FOR 1911 AUTO WILSON COMBAT More Detail

    BULLET PROOF™ FIRING PIN STOPS FOR 1911 AUTO WILSON COMBAT

    Click here for price!$18.99 - $19.99Click here for price!$18.99 - $19.99

    Machined to fit correctly in the slide; holds the extractor in proper relationship to the rim for reliable extraction. Radiused edges prevent stress risers and fatigue cracking. May require minor fitting. 1911, Issue:11, Page:021 Big Book Catalog, Issue:69, Page:114 Sinclair, Issue:1A, Page:020

    HOT!
  • BULLET PROOF™ FIRING PIN STOPS FOR 1911 AUTO WILSON COMBAT More Detail

    BULLET PROOF™ FIRING PIN STOPS FOR 1911 AUTO WILSON COMBAT

    Click here for price!$18.99 - $19.99Click here for price!$18.99 - $19.99

    Machined From Bar Stock To Take A Pounding & Not FailMachined to fit correctly in the slide; holds the extractor in proper relationship to the rim for reliable extraction. Radiused edges prevent stress risers and fatigue cracking. May require minor fitting. 1911, Issue:11, Page:021 Big Book Catalog, Issue:69, Page:114 Sinclair, Issue:1A, Page:020

    HOT!
  • 1911 More Detail

    1911 "TUFF STUFF" EXTRACTOR NOWLIN

    Click here for price!$29.99 - $35.99Click here for price!$29.99 - $35.99

    Fully Machined For Dependability & Long LifeThe same, high-quality extractors that John uses on his own match-winning pistols. Not a casting, but fully machined from solid steel, then specially hardened and cryogenically treated for extra long life and dependable extraction, without taking a set or going flat. Contoured hook helps ensure reliable extraction and chambering. Available to fit Series 70 or relieved for firing pin block to fit Series 80. 1911, Issue:11, Page:011 Big Book Catalog, Issue:69, Page:104 Sinclair, Issue:1A, Page:011

    HOT!
  • LOCKING BLOCK UPGRADE, 92FS (BLOCK, PIN, PLUNGER) BERETTA USA More Detail

    LOCKING BLOCK UPGRADE, 92FS (BLOCK, PIN, PLUNGER) BERETTA USA

    Click here for price!$37.99Click here for price!$37.99

    FITS: Model 90-Two, 9mm; Model 92, 9mm; Model 96, 9mm Big Book Catalog, Issue:68, Page:575 Big Book Catalog, Issue:68, Page:576

    HOT!
  • 1911 HEAVY DUTY EXTRACTOR EGW More Detail

    1911 HEAVY DUTY EXTRACTOR EGW

    Click here for price!$39.99Click here for price!$39.99

    Updated Design For Reliable Extraction & Long Service LifeRedesigned, ruggedly built extractor uses the tighter tolerances and improved geometry possible with 21st century materials and manufacturing technology to deliver outstanding reliability, strength, and durability. Proprietary steel alloy is precision machined with the latest CNC equipment, then vacuum heat-treated to Rc 49-51 for superb strength and tension-retaining properties. All inside corners are radiused to eliminate the sharp 90º corners where failures often occur. Claw is wider than factory specification and undercut and positioned closer to the bolt face for a tighter grip on the case rim. Body is longer, so it can be custom fitted to your slide, and nearly three times as thick as factory original for greater strength. 1911, Issue:11, Page:011 Big Book Catalog, Issue:69, Page:104 Sinclair, Issue:1A, Page:011

    HOT!
  • 1911 FIRING PIN STOP CASPIAN More Detail

    1911 FIRING PIN STOP CASPIAN

    Click here for price!$14.99 - $19.99Click here for price!$14.99 - $19.99

    Upgrade Your Current 1911 Or Build A High-Quality Custom PistolHigh-quality, precision-machined parts from the name that means “custom quality” to serious pistol shooters. Build the ultimate custom 1911 Auto for target, action-pistol, or tactical applications. Repair or return an existing gun to factory specs or assemble a racegun that fits your exact needs. Choose from parts In-the-white or natural-finish stainless. 1911, Issue:11, Page:034 Big Book Catalog, Issue:69, Page:127 Sinclair, Issue:1A, Page:032

    HOT!
  • S&W COMPETITION HAND POWER CUSTOM More Detail

    S&W COMPETITION HAND POWER CUSTOM

    Click here for price!$23.99Click here for price!$23.99

    Oversize For Fitting & Correcting TimingNo more heating and bending factory hands to correct faulty cylinder timing. Oversize dimensions can be easily fitted to all S&W "K", "L" and "N" frame revolvers. Machined from tool steel, heat treated and then precision ground to final dimensions. Big Book Catalog, Issue:69, Page:230 Big Book Catalog, Issue:69, Page:231

    HOT!
  • FIRING PIN GLOCK More Detail

    FIRING PIN GLOCK

    Click here for price!$39.99Click here for price!$39.99

    FITS: Model 22, .40 S&W; Model 23, .40 S&W; Model 27, .40 S&W; Model 31, .357 SIG; Model 32, .357 SIG; Model 33, .357 SIG; Model 35, .40 S&W Firing Pin - fits .40, .357, .45 GAP (has 2 dashes approx ½ inch from tip ) “GLOCK” is a federally registered trademark of Glock, Inc. and is one of many trademarks owned by Glock, Inc. or Glock Ges.m.b.H. Brownells is an independent dealer of parts and accessories for Glock® pistols, and is not affiliated with or endorsed by Glock, Inc. or Glock Ges.m.b.H. The use of Glock on this page is merely to advertise the sale of Glock parts or components. As indicated in the product descriptions, not all parts and accessories on this site are official Glock products. Big Book Catalog, Issue:68, Page:606 Big Book Catalog, Issue:68, Page:607 Big Book Catalog, Issue:68, Page:608

    HOT!
  • FAILURE RESISTANT EXTRACTORS APEX TACTICAL SPECIALTIES INC. More Detail

    FAILURE RESISTANT EXTRACTORS APEX TACTICAL SPECIALTIES INC.

    Click here for price!$45.99 - $75.00Click here for price!$45.99 - $75.00

    Drop-in replacements for factory components enhance reliability and optimize the performance of your M&P for different applications. Although no gun part can be absolutely failure “proof,” this upgraded extractor helps prevent one of the M&P’s few weaknesses: occasional extraction failures. The FRE is designed to ensure consistent, reliable extraction under highly adverse conditions. Engagement surfaces are wire electrical discharge machined (EDM) to precise tolerances for a drop-in fit (usually—individual guns may require minor fitting) and exceptional reliability and function. With the FRE installed, M&P shooters have reported as many as 2,500 rounds through their pistols without a single extraction failure. Note: Does not fit the M&P Shield Pistol. Big Book Catalog, Issue:69, Page:225

    HOT!
  • SWJ-200 PRO-SPRING KIT FOR S&W J-FRAME REVOLVER BROWNELLS More Detail

    SWJ-200 PRO-SPRING KIT FOR S&W J-FRAME REVOLVER BROWNELLS

    Click here for price!$10.40Click here for price!$10.40

    "Guaranteed Superior"Kit contains (3) different, rate reduced power rebound springs, 13, 14 and 15 lb., to give you the proper selection; plus (1) reduced power hammer spring. Big Book Catalog, Issue:69, Page:232

    HOT!
  • 1911 BULLET PROOF™ FIRING PIN WILSON COMBAT More Detail

    1911 BULLET PROOF™ FIRING PIN WILSON COMBAT

    Click here for price!$14.99Click here for price!$14.99

    Machined to exact tolerances, then heat treated for many times the service life of a standard firing pin. Available for .38/9mm and .45 ACP. 1911, Issue:11, Page:021 Big Book Catalog, Issue:69, Page:114 Sinclair, Issue:1A, Page:020

    HOT!
  • S&W SDVE SPRING KIT APEX TACTICAL SPECIALTIES INC. More Detail

    S&W SDVE SPRING KIT APEX TACTICAL SPECIALTIES INC.

    Click here for price!$20.95Click here for price!$20.95

    The Apex Spring Kit for the SDVE produces a smoother trigger pull and improved reset and is designed for Duty/Carry use. The kit works as a stand-alone or in conjunction with the Apes Polymer Action Enhancement Trigger for the SDVE. NOT for use in the Sigma Series pistols.

    HOT!
  • 1911 FIRING PIN STI More Detail

    1911 FIRING PIN STI

    Click here for price!$9.99 - $28.99Click here for price!$9.99 - $28.99

    Long Wearing Steel & Ultra-Lightweight TitaniumSteel - Precision machined from long-wearing stainless steel; hardened and relieved for increased shock-resistance. Titanium - Dramatically lowers lock time. 1911, Issue:11, Page:021 Big Book Catalog, Issue:69, Page:114 Sinclair, Issue:1A, Page:020

    HOT!
  • FIRING PIN & EXACT EDGE EXTRACTOR VOLQUARTSEN More Detail

    FIRING PIN & EXACT EDGE EXTRACTOR VOLQUARTSEN

    Click here for price!$28.99 - $33.99Click here for price!$28.99 - $33.99

    Fits Ruger® MKI, MKII™, & MKIII™ including 22/45™. Firing pin sold with extractor or available separately. Firing Pin EDM machined from A2 tool steel Minimizes/eliminates light hits Firing pin strike face is surface ground Firing pin is .004" wider than factory pin, new width helps eliminate side-to-side movement Hardened to RC56-58 to prevent deformation Extractor EDM machined from A2 tool steel Allows for exact tolerances Will not lose edge under impact Precise hook point is hardened to RC58-60

    HOT!
  • S&W EXTRA LENGTH FIRING PIN POWER CUSTOM More Detail

    S&W EXTRA LENGTH FIRING PIN POWER CUSTOM

    Click here for price!$13.99Click here for price!$13.99

    Power Customs Extra Length Firirng Pin is made from heat treated, S7 tool steel and is compatable with post 1997 Smith & Wesson J, K, L, N, and X frame revolvers.

    HOT!
  • 1911 BULLET PROOF TITANIUM FIRING PIN WILSON COMBAT More Detail

    1911 BULLET PROOF TITANIUM FIRING PIN WILSON COMBAT

    Click here for price!$29.99Click here for price!$29.99

    The Bullet Proof ® Titanium firing pin is a simple drop-in retrofit for shooters who want to enhance drop safety and reduce lock time in their 1911. This part is a drop-in part for Series 70 or Series 80 style 1911 designs and for guns with a standard .45 ACP USGI/Colt diameter (.093”) firing pin. 1911, Issue:11, Page:021 Big Book Catalog, Issue:69, Page:114

    HOT!
  • RUGER® BLACKHAWK® EJECTOR ROD HOUSING BORCHARDT RIFLE More Detail

    RUGER® BLACKHAWK® EJECTOR ROD HOUSING BORCHARDT RIFLE

    Click here for price!$25.00Click here for price!$25.00

    Replaces The Factory Aluminum Part Made from durable, machined steel that wears longer and functions smoother than the factory aluminum part. Increased weight helps cut down muzzle flip. High-lustre blue finish adds a touch of class to your Ruger® Blackhawk® revolver. Big Book Catalog, Issue:67, Page:229

    HOT!
  • SWK/L/N-202 PRO-SPRING KIT FOR S&W K,L,N FRAME REVOLVER BROWNELLS More Detail

    SWK/L/N-202 PRO-SPRING KIT FOR S&W K,L,N FRAME REVOLVER BROWNELLS

    Click here for price!$19.99Click here for price!$19.99

    "Guaranteed Superior"Standard power kit with a Power Rib mainspring that duplicates the factory spring's rate. Gives positive ignition of magnum primers, vastly improved smoothness and consistency of pull. Includes 13, 14, and 15 lb. rebound springs for precise tuning. Big Book Catalog, Issue:69, Page:232

    HOT!
  • OVERSIZE CYLINDER STOP POWER CUSTOM More Detail

    OVERSIZE CYLINDER STOP POWER CUSTOM

    Click here for price!$27.99Click here for price!$27.99

    Improve Function & Accuracy in S&W RevolversInstall one of these oversize cylinder stops to help improve the function and accuracy of worn and loose Smith & Wesson K, L, and N frame revolvers. CNC machined from A-2 tool steel, these stops are slightly oversized in width to allow for worn frame windows and cylinder notches. Big Book Catalog, Issue:69, Page:230

    HOT!

Subscribe our newsletter

Lorem ipsum dolor sit amet, consectetur adipisicing elit. Ex, velit!